Archive for jewelry – Page 2

Christmas Charms Pendant by Rhea Weigand

SSC1183_2_RW_800Supplies:

From Stampendous:

SSC1183 Christmas Charms

FRG11C Red Glass Glitter

FRG02C Champange Glass Glitter

FRC11 Scarlet Color Fragments

FRC13 Leaf Green Color Fragments

Plus:

Old Book Page

Tuxedo Black Memento Ink by Tsukineko

Art Mechanique Bezels by Spellbinders®

Ball Chain and Watch Gears

Red and Green ink pads

ICE Resin

Red Sheer Organdy Ribbon by May Arts

Instructions:

  1. Stamp images in black, red and green on aged book paper. Trim to fit Bezel.
  2. Glue down in Bezel.
  3. Place in Bezel.
  4. Add gears, chain, and Glass Glitter and glue in place.
  5. Mix ICE Resin according to directions and pour into Bezel. Let Dry

Christmas Charms Pendant by Rhea Weigand

SSC1183_RWSupplies:

From Stampendous:

SSC1183 Christmas Charms Perfectly Clear Stamps

FRG11C Red Glass Glitter

FRG12C Green Glass Glitter

FRG02C Champagne Glass Glitter

SSH38 Small Acrylic Handle

STF082 VersaFine™ Onyx Black Ink Pad

Plus:

Art Mechanique Heart Bezel by Spellbinders®

White Cardstock

Miniature Gears and Embellishments

EnviroTex® Jewelry Resin

Red Silk Ribbon from May Arts

 

Instructions:

  1. Stamp images on cardstock. Color as desired.
  2. Cut to fit Bezel and place inside.
  3. Add Glass Glitter and gears.
  4. Mix EnviroTex according to directions and pour in Bezel.
  5. Let dry over night.
  6. Add charms, ribbons or chain.

Vintage Ladies Resin Necklace by Debbie Cole

Vintage Ladies Resin Necklace by Debbie ColeSupplies:

From Stampendous:
SSC1136 Vintage Ladies Perfectly Clear Stamps
SSH38 Small Perfectly Clear Acrylic Handle

Plus:
Media Mixage Antique Bronze Large Square Bezel by Spellbinders
ICE® Resin
Americana Deep Burgundy, Flesh Tone, Forest Green, Lamp Black, Traditional Raw Sienna, Traditional Burnt Umber, & Victorian Blue Acrylic Paint by DecoArt®
Easy Float by DecoArt®
Paintbrushes
Sponge Wedges
White Cardstock
Bubble Palette
Paper Towels
Glue
Cog & Gears
Necklace Chain
Jump Rings & Lobster Claw Closure
Rhinestones
Craft Sticks
Disposable Measuring Cups
Detail Scissors

Instructions:

  1. Place the text stamp onto an acrylic handle. Dampen a cosmetic sponge and remove as much water as possible. Pour a puddle of Traditional Burnt Umber out on the palette paper. Pounce the sponge into the paint and then on a clean area of the palette. When you look at the bottom of the sponge it should be covered by paint but you should still be able to see the texture of the sponge. Pounce the sponge onto the stamp and stamp on the card stock. Using the same sponge, reload with the Traditional Burnt Umber and stamp the remaining images in the same manner.
  2. Cut the stamped text to fit into the bezel. If you have the die, you can run it through your machine. Using a bubble palette, place about a dime size drop of Traditional Raw, Flesh Tone, Victorian Blue, Forest Green, and Deep Burgundy into individual bubbles. Mix one part paint with appx three parts water mixed with Easy Float. Completely mix the paint until it becomes transparent. Using #8 shader wash Traditional Raw Sienna mixture over the entire background and also the ladies hair. Wash the lady’s face and arms with Flesh Tone mix, her corset with Victorian Blue mix, the rose with Deep Burgundy mix, and it’s leaves with Forest Green mix. Cut out when dry.
  3. Seal the images and background with all purpose glue, allow to dry, and repeat step. Glue background into the bezel. Mix Ice Resin according to manufacturer’s instruction and pour small amount into the bezel. It should cover the entire bottom, but one third of the depth. Allow to harden.
  4. Place remaining images and watch gears into bezel. Mix Ice Resin according to manufacturer’s instruction and pour small amount into the bezel. It should cover the entire another third of the depth. Allow to harden.
  5. Place rhinestones around the inside of the bezel, gluing into place. Mix additional Ice Resin and fill bezel. Allow to harden over night.
  6. Add charms, cogs, and chain of choice using jump rings.

Steampunk Charms Resin Necklace by Debbie Cole

Steampunk Charms Resin Necklace by Debbie ColeSupplies:

From Stampendous:
SSC1179 Steampunk Charms
SSC38 Small Perfectly Clear Acrylic Handle

Plus:
Media Mixage Antique Bronze Medium Rectangle Bezel by Spellbinders
Americana Traditional Raw Sienna & Traditional Burnt Umber Acrylic Paint by DecoArt®
Easy Float by DecoArt®
ICE® Resin
Sponge Wedges
Glue
Bubble Palette
Paper Towel
Cogs & Gears
Antique Bronze Necklace Chain
Antique Bronze Jump Rings
Antique Bronze Lobster Claw Closure
Rhinestones
Craftsticks
Disposable Measuring Cups
Detail Scissors

Instructions:

  1. Place the text stamp onto an acrylic handle. Dampen a cosmetic sponge and remove as much water as possible. Pour a puddle of Traditional Burnt Umber out on the palette paper. Pounce the sponge into the paint and then on a clean area of the palette. When you look at the bottom of the sponge it should be covered by paint but you should still be able to see the texture of the sponge. Pounce the sponge onto the stamp and stamp on the light brown card stock. Using the same sponge, reload with the Traditional Burnt Umber and stamp the remaining images onto the off white card stock.
  2. Cut the stamped text to fit into the bezel. If you have the die, you can run it through your machine. Seal the paper with all purpose glue, allow to dry, and repeat step. Mix Ice Resin according to manufacturer’s instruction and pour small amount into the bezel. It should cover the entire bottom, but only half the depth. Allow to harden.
  3. Using a bubble palette, place about a dime size drop of Traditional Raw into an individual bubble. Mix one part paint with approximately three parts water mixed with Easy Float. Completely mix the paint until it becomes transparent. Using #8 shader wash over the remaining images. Cut out when dry. Seal in the same manner as the background. Glue the balloons,and small watch gears into place in the bezel and the man onto a cog. Mix Ice Resin and pour to fill bezel. Pour a small amount over the man on the cog. Allow to set for two hours. Place three rhinestones onto the upper right hand corner of the bezel. They will stick to the resin. Allow to harden over night.Glue man on cog into lower left hand corner. Add charms, cogs, and chain of choice using jump rings.

Stack Art Angel Wings Clay Tag by Debbie Cole

Stack Art Angel Wings Clay Tag by Debbie ColeSupplies:

From Stampendous:
SAK01 Stack Art Kraftboard Angel Wings
SAS01 Stack Art Stamps Angel Wings

Plus:
Americana Lamp Black, True Blue, & Ultra Deep Blue Acrylic Paint by DecoArt®
Dazzling Metallics Glorious Gold Acrylic Paint by DecoArt®
DuraClear Matte Varnish by DecoArt®
Paintbrushes
Bronze Polymer Clay
ICE® Resin
Oval Bezel
Blue Rhinestones
Sponge Wedges
X-Acto® Knife
1″ Square Shape Cutter
Cogs & Watch Parts
Cardstock
Glue

Instructions:

  1. Knead the clay so that it is soft and workable. Roll in a ball and roll the clay out using a rolling pin or acrylic roller to 1/4 inch in depth. Apply Damask stamp onto an acrylic handle. Spray the  stamp with a light mist of water and press firmly into the clay. Lift the stamp off the clay. Remove the large stack art kraftboard.  Use the negative space as a template to cut out the clay shape with an X-Acto Knife. Cut the wings in the same manner. Roll a small ball of clay and place into oval bezel. Bake all shapes in a toaster oven according to manufacturer’s instructions. Allow to cool.
  2. Paint the background with True Blue, wiping off the paint to reveal the clay underneath. Add Ultra Blue Deep only in the deep crevices of the clay using a #3 round brush. Dry brush highlights to background and wings and wash over the face with Glorious Gold.  Dampen cosmetic sponge and remove as much water as possible. Pour a puddle of Lamp Black out on the palette paper. Pounce the sponge into the paint and then on a clean area of the palette. When you look at the bottom of the sponge it should be covered by paint but you should still be able to see the texture of the sponge. Quickly pounce the loaded sponge over the face stamp. Stamp it onto the clay in oval bezel. Glue all elements together adding blue crystals.
  3. Mix Ice Resin according to manufacturer’s instructions. Brush ATC as a varnish with a disposable brush. Allow to harden overnight.